Count Code Converter / Countdown Display

CS-5 x 4 Reader

Reads CS-5246 x 4, IRIG B-12x, CS-5, Auto Baud Detection.

Has an IRIG B settable offset for local time. Converts IRIG B to a CS-5 output signal for a standard CS-5 RDU display…

READ MORE

Features:

Reads CS-5246 x 4, IRIG B-12X, CS-5, Auto Baud Rate Detection

RG B Output as A Pseudo CS-5 Signal for CS-5 RDU Display

Intensity Control with optional leading zero suppression

Two Independent 15 character 0.56″ high LED display

Display event count, launch time or IRIG-B on either display

Selected count output as CS-524x for each display

First motion contacts (output) for each display\

with Ethernet network control port

Model CS5X4R-1

Also Available with Dual power supply
Model CS5X4R-1 DPS
                                                  

The 8.4 DRM Monitor

Dual 8.4 high definition TFT LCD display (available with SVGA or XGA native screen resolution)

Accepts composite, component, S-video, VGA and DVI inputs standard along with NTSC/ PAL/ and SECAM standards. Supports SD and HD-SDI with repeated (re-clocked) outputs.

READ MORE

Features:

Dual 8.4 ” High Definition TFT LCD Displays
Available with SVGA or XGA native screen resolution
19″ wide 4 RU tilt-able for easy viewing
Accepts composite, component, S-Video, VGA, and DVI inputs standard
Analog RGB and YPrPb component inputs standard
Optional single or dual SD or HD-SDI input with repeater (re-clocked) output
Front mounted push button OSD for simple operation.
4 Programmed function keys for instant access
Green/ Blue/Red screen options for set-up adjust

Specifications:

19″ wide x -RU (7″) High x 3.5″ Deep
Weighs 5.5 pounds
For SVGA Screen (800 x 600)
Brightness 450 nits
262,000 colors
Contrast Ratio 500:1
View Angle (H/V) 120/100
For XGA Screen (1024 x 768)
RGB Vertical Stripe
16.7M  Colors
2-CCFL tube backlights-replaceable
Anti glare and hard coating surface treatment50,000 hour backlight life expectancy
100% digital signal processing for each display
Picture in Picture (PIP) feature for each display
Optional Dual or Single channel SDI card accepts SD or HD-SDI with repeated output(s)

RDU 1.2

16 digit alpha numeric dot matrix display. Reads IRIG-B, CS-5×4, CS-3, MILA, CS524x and display either the EC (even count) field or the LT (launch time) field.

Both CS524x or 5×4 may be displayed with decimal seconds or without both signals. Will read with automatic baud rate detection.

READ MORE

Specifications:

Power Input: 90-265, VAC 47-470 Hz, IEC
Input connector 10w nominal
Half highlight* 175
Full highlight* 235
Fuse: 1 AMP
Dimensions: 19″w  x  3.50″ H (2 RU ) x 5.0″ deep
Weight: 4.0LBS
Operating Environment: 32 F to 100 F, 0-95%
RH NON condensing
Signal Inputs:
IRIG-B modulated code, CS-3, or MILA 10mV to 10 V P-P
10k ohm input impedance, isolated BNC connector with transformer (balanced) isolation.
CS-524x or CS-5 x 4 at 4800, 9600, or 19.2k baud. Automatic baud rate detection, RS- 422
input on twinax (BJ-77) and DB-9 female connector.Signal Outputs:Digital buffered output RS-422 on  DB-9 female connector. DB-9 female connector has
first motion (MLO) relay contacts. N.O. and N.C contacts are available.Ethernet Port: A 10-100 base T port for control and status.
RS-232 Port: Either network or local RS-232 can be used for control.

Features:

Reads CS 524x, CS-5×4, CS-5, CS-3, MILA and IRIG-B

16 digit alpha numeric dot matrix display

Will read CS-524x and display either the EC (Event Count) field or the LT (launch time) field.

Both CS524x or CS- 5X4 may be displayed with decimal seconds or without.Both signals will be read with automatic baud rate detection.

Colons are displayed optionally, the display may be configured to display accumulated seconds in both CS-5 and IRIG-B display modes.

Leading zero blanking may be selected two mode are available straight left to right leading zero suppression or left to right per grouping leading zero suppression (per group is defined as days, hours, minutes, and seconds)

Portable VDA

Dual 8.4 high definition TFT LCD display

(available with SVGA or XGA native screen resolution)

Portable VDA has a rugged die -cast aluminum case fully insulated from circuitry.

READ MORE

Specifications:

Power 9-18 Volt AC or DC
Power Connector:

Standard 4 pin XLR
(pins  and 4. No polarity)

Dimensions: 4 ½ x 3/8 x 1 3/8 overall
Weight: 10oz
Input / Output Connectors BNC

Electrical  Performance:

Input 75 Ohm terminated. 1 Volt P-P
NTSC, PAL, or SECAM Video
Input Signal Range

-1.5 to +  1.5V (DC coupling)

Outputs Configured as 2 groups of 2
Frequency Flat  to 20 MHz (.1dB), DC to 50 MHz. (3Db)
Gain Switchable per group, 0 dB or + 1 dB
Cable Equalization Switchable per group, 0 dB or + 1 dB @ 5 MHz
Equalizes approximately 450ft. of  RG-59u cable
Differential Gain < 0.1%
Differential Phase < 0.1% Degrees
Output to Output Isolation -50dB per group,
-60 dB between groups @  1 MHz

Dual RDU 1.2

Dual 16 digit alpha numeric dot matrix display reads CS-524, CS-5+4, CS5x8, CS-3, MILA, IRIG-B, and 109-64 with optional PCB.

Can read two counts at once or any two display option same features as our RDU 1.2.

READ MORE

Specifications:

Power Input: 90-265, VAC 47-470 Hz, IEC Input connector 10w nominal
Fuse 1 AMP
Dimensions 235
Fuse: 1 AMP
Dimensions: 19″w x 1.75 H (1 RU ) x 10.25 deep
Weight: 4.5LBS
Operating Environment: 32 F to 100 F, 0-95% RH NON condensing

Signal Inputs: 

IRIG-B modulated code, CS-3, or MILA 10mV to 10 V P-P
10k ohm input impedance, isolated BNC connector with transformer (balanced) isolation.

CS-524x or CS-5 x 4 at 4800, 9600, or 19.2k baud. Automatic baud rate detection, RS- 422
input on twinax (BJ-77) and DB-9 female connector.

Signal Outputs:

Digital buffered output RS-422 on  DB-9 female connector. DB-9 female connector has
first motion (MLO) relay contacts. N.O. and N.C contacts are available.

Ethernet Port: A 10-100 base T port for control and status.
RS-232 Port: Either network or local RS-232 can be used for control.

Features:

Reads CS 524x, CS-5×4, CS-5, CS-3, MILA and IRIG-B

16 digit alpha numeric dot matrix display

Will read CS-524x and display either the EC (Event Count) field or the LT (launch time) field.

Both CS524x or CS- 5X4 may be displayed with decimal seconds or without.Both signals will be read with automatic baud rate detection.

Colons are displayed optionally, the display may be configured to display accumulated seconds in both CS-5 and IRIG-B display modes.

Leading zero blanking may be selected two mode are available straight left to right leading zero suppression or left to right per grouping leading zero suppression (per group is defined as days, hours, minutes, and seconds)

Text display mode displays static text message. Any text message may be entered manually, Through the R5-232 port, or
through the network port.

Up to 16 ASCII characters may be displayed. The message will be stored in EEPROM to prevent loss.